Our Full Spectrum of Barrier System Panels and Accessories

ADJUSTABLE PANELS

10’ Tall

Our 48″ panels are 7′-8″ tall and extend to 10′-0″. The adjustable upper panel, shown above, slides up to the height of the ceiling. To adjust the height you simply loosen the knurled knob on each side, slide the panel up to the ceiling, then retighten the knobs.

The 48″ panels are our work horse panel. They allow you to enclose large areas very quickly. Setup time for this panel is about 2 minutes.

Our 48″ panels include a self leveling channel on the bottom to compensate for unlevel floors. This channel has a neoprene gasket adhered to the bottom side to create a seal to the floor.
The sides of the panel contain closed cell gasket material to form a seal between the panels and the top of the panel has a 1/4″ thick soft ether foam gasket to conform to the ceiling.

Grid clips and camlocks are included with the panels.

Opal – P/N 4000 – $640.00

Transparent – P/N 4000T – $640.00

Clear – P/N 4000C – $680.00

All panels are available in Transparent, Opal and Clear

4001 3' Panel Assembly_1

Our 36″ panels are 7′-8″ tall and extend to 10′-0″. The adjustable upper panel, shown above, slides up to the height of the ceiling. To adjust the height you simply loosen the knurled knob on each side, slide the panel up to the ceiling, then retighten the knobs.

The 36″ panels, like the 12″ panels, are typically used for odd shaped configurations. It’s nice to have a couple on hand but the 48″ panels should be used when possible. Setup time for this panel is about 2 minutes.

Our 36″ panels include a self leveling channel on the bottom to compensate for unlevel floors. This channel has a neoprene gasket adhered to the bottom side to create a seal to the floor.
The sides of the panel contain closed cell gasket material to form a seal between the panels and the top of the panel has a 1/4″ thick soft ether foam gasket to conform to the ceiling.

Grid clips and camlocks are included.

Opal – P/N 4001 – $605.00

Transparent – P/N 4001T – $605.00

Clear – P/N 4001C – $640.00

All panels are available in Transparent, Opal and Clear dust barrier panels building construction – general contractors and operative builders residential construction

Our 24″ panels are 7′-8″ tall and extend to 10′-0″. The adjustable upper panel slides up to the height of the ceiling. To adjust the height you simply loosen the knurled knob on each side, slide the panel up to the ceiling, then retighten the knobs. We offer several options on our 24″ panels.

Our 24″ panels include a self leveling channel on the bottom to compensate for unlevel floors. This channel has a neoprene gasket adhered to the bottom side to create a seal to the floor.

The sides of the panel contain closed cell gasket material to form a seal between the panels.

The top of the panel has a 1/4″ thick soft ether foam gasket to conform to the ceiling.

Grid clips and camlocks are included with the panels.

4002 is our standard 24″ panel. dust barrier panels building construction – general contractors and operative builders Hospital Renovation, Safety, Hospital Construction

Opal – P/N 4002 – $475.00

Transparent – P/N 4002T – $475.00

Clear – P/N 4002C – $500.00

Opal – P/N 4002.1 $475.00

Transparent – P/N 4002.1T – $475.00

Clear – P/N 4002.1C – $500.00

All panels are available in Transparent, Opal and Clear

4002.1 is our standard panel with a port to exhaust HEPA filtered air out of the containment area. This port has an 8″ I.D. and a 10″ O.D. on both the inside and outside of the panel.

An 8″ diameter plug is tethered to the inside of the panel to close the port off when not in use.

Our 24″ panels are 7′-8″ tall and extend to 10′-0″. The adjustable upper panel slides up to the height of the ceiling. To adjust the height you simply loosen the knurled knob on each side, slide the panel up to the ceiling, then retighten the knobs. We offer several options on our 24″ panels.

Our 24″ panels include a self leveling channel on the bottom to compensate for unlevel floors. This channel has a neoprene gasket adhered to the bottom side to create a seal to the floor.

The sides of the panel contain closed cell gasket material to form a seal between the panels.

The top of the panel has a 1/4″ thick soft ether foam gasket to conform to the& ceiling.

Grid clips and camlocks are included with the panels.

4002 is our standard 24″ panel. dust barrier panels building construction – general contractors and operative builders Hospital Renovation, Safety, Hospital Construction

Opal – P/N 4002 – $475

Transparent – P/N 4002T – $475

Clear – P/N 4002C – $500

Opal – P/N 4002.1 $550

Transparent – P/N 4002.1T – $550

Clear – P/N 4002.1C – $570

All panels are available in Transparent, Opal and Clear

4002.1 is our standard panel with a port to exhaust HEPA filtered air out of the containment area. This port has an 8″ I.D. and a 10″ O.D. on both the inside and outside of the panel.

An 8″ diameter plug is tethered to the inside of the panel to close the port off when not in use.

Our 36″ panels are 7′-8″ tall and extend to 10′-0″. The adjustable upper panel, shown above, slides up to the height of the ceiling. To adjust the height you simply loosen the knurled knob on each side, slide the panel up to the ceiling, then retighten the knobs.

The 36″ panels, like the 12″ panels, are typically used for odd shaped configurations. It’s nice to have a couple on hand but the 48″ panels should be used when possible. Setup time for this panel is about 2 minutes.

Our 36″ panels include a self leveling channel on the bottom to compensate for unlevel floors. This channel has a neoprene gasket adhered to the bottom side to create a seal to the floor.
The sides of the panel contain closed cell gasket material to form a seal between the panels and the top of the panel has a 1/4″ thick soft ether foam gasket to conform to the ceiling.

Grid clips and camlocks are included.

Opal – P/N 4006 $315.00

Transparent – P/N 4006T $315.00

Clear – P/N 4006C $325.00

All Panels are available in Transparent, Opal and Clear

Our 6″ panels are 7′-8″ tall and extend to 10′-0″. The adjustable upper panel, shown above, slides up to the height of the ceiling. To adjust the height you simply loosen the knurled knob on each side, slide the panel up to the ceiling, then retighten the knobs.

4005 is our 6″ panel. $265.00 It’s nice to have a couple on hand to use as fillers for odd shaped areas.

Our 6″ panels include a self leveling channel on the bottom to compensate for unlevel floors. This channel has a neoprene gasket adhered to the bottom side to create a seal to the floor.

The sides of the panel contain closed cell gasket material to form a seal between panels and the top of the panel has a 1/4″ thick soft ether foam gasket to conform to the ceiling.

Grid clips and camlocks are included with the panels.

Opal – P/N 4000 – $290.00

Transparent – P/N 4000T – $290.00

Clear – P/N 4000C – $305.00

All panels are available in Transparent, Opal and Clear

Hinged Corner Assembly Allows you to make transitions from 90 degrees to about 170 degrees. The simplest way to create angles is to connect the corner to the two mating panels at 90 degrees, then swing one panel to the angle you desire.

Hinged Corner Assembly Product number: 4004

Price: $200.00

Outside Corner Post

Outside Corner Post – P/N 4007 – $170.00

T-Post Assembly

Product Number: 4009

Price: $170.00

​A T-Post allows you to form an intersection with panels.

Dimensions: 7′ x 8″ Tall by 2″ wide ​with an adjustable slider that can reach a height of 10′

12’ Tall

These panels are 7’8”  tall and extend to 12′-0″. The adjustable upper panel, shown above, slides up to the height of the ceiling. To adjust the height you simply loosen the knurled knob on each side, slide the panel up to the ceiling, then retighten the knobs.

The 48″ panels are our work horse panel. They allow you to enclose large areas very quickly. Setup time for this panel is about 2 minutes.

Our 48″ panels include a self leveling channel on the bottom to compensate for unlevel floors. This channel has a neoprene gasket adhered to the bottom side to create a seal to the floor.
The sides of the panel contain closed cell gasket material to form a seal between the panels and the top of the panel has a 1/4″ thick soft ether foam gasket to conform to the ceiling.

Grid clips and camlocks are included with the panels.

Opal – P/N 4020 – $710.00

Transparent – P/N 4020T – $710.00

Clear – P/N 4020C – $710.00

All panels are available in Transparent, Opal and Clear

Our 36″ panels are 7′-8″ tall and extend to 12′-0″. The adjustable upper panel, shown above, slides up to the height of the ceiling. To adjust the height you simply loosen the knurled knob on each side, slide the panel up to the ceiling, then retighten the knobs.

The 36″ panels, like the 12″ panels, are typically used for odd shaped configurations. It’s nice to have a couple on hand but the 48″ panels should be used when possible. Setup time for this panel is about 2 minutes.

Our 36″ panels include a self leveling channel on the bottom to compensate for unlevel floors. This channel has a neoprene gasket adhered to the bottom side to create a seal to the floor.
The sides of the panel contain closed cell gasket material to form a seal between the panels and the top of the panel has a 1/4″ thick soft ether foam gasket to conform to the ceiling.

Grid clips and camlocks are included.

Opal – P/N 4021 – $660.00

Transparent – P/N 4021T – $660.00

Clear – P/N 4021C – $660.00

All panels are available in Transparent, Opal and Clear

Our 24″ panels are 7′-8″ tall and extend to 12′-0″. The adjustable upper panel slides up to the height of the ceiling. To adjust the height you simply loosen the knurled knob on each side, slide the panel up to the ceiling, then retighten the knobs. We offer several options on our 24″ panels.

Our 24″ panels include a self leveling channel on the bottom to compensate for unlevel floors. This channel has a neoprene gasket adhered to the bottom side to create a seal to the floor.

The sides of the panel contain closed cell gasket material to form a seal between the panels.

The top of the panel has a 1/4″ thick soft ether foam gasket to conform to the ceiling.

Grid clips and camlocks are included with the panels.

Opal – P/N 4022 $530.00

Transparent – P/N 4022T $530.00

Clear – P/N 4022C $530.00

All panels are available in Transparent, Opal and Clear

Coming Soon

Coming Soon

Coming Soon

Coming Soon

Our 6″ panels are 7′-8″ tall and extend to 12′-0″. The adjustable upper panel, shown above, slides up to the height of the ceiling. To adjust the height you simply loosen the knurled knob on each side, slide the panel up to the ceiling, then retighten the knobs.

4005 is our 6″ panel. It’s nice to have a couple on hand to use as fillers for odd shaped areas.

Our 6″ panels include a self leveling channel on the bottom to compensate for unlevel floors. This channel has a neoprene gasket adhered to the bottom side to create a seal to the floor.

The sides of the panel contain closed cell gasket material to form a seal between panels and the top of the panel has a 1/4″ thick soft ether foam gasket to conform to the ceiling.

Grid clips and camlocks are included with the panels.

Opal – P/N 4025 $325.00

Transparent – P/N 4025T $325.00

Clear – P/N 4025C $325.00

All panels are available in Transparent, Opal and Clear

Our 12” panels are 7′-8″ tall and extend to 12′-0″. The adjustable upper panel, shown above, slides up to the height of the ceiling. To adjust the height you simply loosen the knurled knob on each side, slide the panel up to the ceiling, then retighten the knobs.

The 12″ panels are typically used for odd shaped configurations. It’s nice to have a couple on hand but the 48″ panels should be used when possible. Setup time for this panel is about 2 minutes.

Our 12″ panels include a self leveling channel on the bottom to compensate for unlevel floors. This channel has a neoprene gasket adhered to the bottom side to create a seal to the floor.
The sides of the panel contain closed cell gasket material to form a seal between the panels and the top of the panel has a 1/4″ thick soft ether foam gasket to conform to the ceiling.

Grid clips and camlocks are included.

Opal – P/N 4026 $350.00

Transparent – P/N 4026T $350.00

Clear – P/N 4026C $350.00

All panels are available in Transparent, Opal and Clear

Coming Soon

Coming Soon

Coming Soon

Coming Soon

Coming Soon

14’ Tall

Coming Soon

Coming Soon

Coming Soon

Coming Soon

Coming Soon

Coming Soon

Coming Soon

Coming Soon

Coming Soon

Coming Soon

Coming Soon

Coming Soon

Coming Soon

Coming Soon

Coming Soon